Comtech EF Data DMD-2050E Specifications Page 111
- Page / 342
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
Rated. / 5. Based on customer reviews
DMD2050E Universal Satellite Modem Theory of Operation
MN-DMD2050E Revision 2 3–69
3.21 Locating the DMD2050E ID Code Operational Procedure
Unique ID codes let you add feature upgrades to the unit. You do not have to return the unit to
the factory.
After you purchase new features, Comtech EF Data gives you a new ID code. Enter the new ID
code into the unit to activate the new features.
Find the unique ID Code:
1. Make sure that the unit is on.
2. Use the Arrow Keys ()on the front panel to go to the System Menu. This is the
top-level menu.
3. Press the Down Arrow once, then press the Left Arrow once to go to the HW/FW
Config Screen.
4. Press the Down Arrow once, then press the Left Arrow once to go to the Features
Screen.
5. Press the Down Arrow once.
A two-row screen appears . The top row is the unique ID number for the unit. It is a 12-
digit code (3 sets of 4 digits). Write down the unique ID number for your
Comtech EF Data sales representative.
The second row shows three groups of dashes (----.----.----). The dashes show where to
enter the new ID code given to you by Comtech EF Data.
6. Use the number keys on the front panel to enter the new ID code from Comtech EF Data
and press
ENTER.
If the new ID code is accepted (within three attempts), the screen shows “Upgrade Mgr:
Entry Accepted” and the new features are unlocked. After the new features are unlocked,
dashes (----.----.----) replace the new ID code on the screen.
If the new ID code is not accepted, the display shows “Further Attempts Require a
Reboot”. You must stop and start the power before you can try again.
####.####.####
----.----.----
- DMD-2050E 1
- BLANK PAGE 10
- Table of Contents 11
- vii 15
- viii 16
- xii 20
- xiii 21
- xiv 22
- Figures 23
- xvi 24
- PREFACE 25
- Electrical Safety 26
- Battery 26
- Grounding 26
- Environmental 27
- Low Voltage Directive (LVD) 27
- CE Mark 28
- Preface MN-DMD2050E 29
- Chapter 1. Introduction 31
- 1.2 DMD2050E Configurations 32
- 1.2.1 Features 32
- 1.2.3 Bandwidth Compression 33
- 1.2.4 Interfaces 34
- 1.2.6 Compatibility 34
- 1.2.7 Physical Description 34
- Chapter 2. Installation 37
- 2.2 Installation Safety 38
- 2.3.1 Location 39
- 2.3.2 Airflow 39
- 2.3.3 Temperature 39
- 2.3.4 Electrical Power 39
- 2.3.5 Cables 40
- 2.5 Modulator Checkout 41
- 2.5.1 Initial Start Up 41
- 3.1 DMD2050E Hardware 43
- 3.2.1 Front Panel 47
- 3.2.2 Baseband Processing 47
- 3.2.6 Terminal Port 50
- 3.2.8 Ethernet M&C Port 51
- 3.2.9 Modem Monitor Status 51
- 3.3 Internal Clock 52
- 3.5.1 Clock Selection 55
- 3.5.2 TX Clock Options 56
- 3.5.3.1 RX SAT Clock 58
- Clock specification 59
- Frequency 1 MHz to 20 MHz 59
- 3.6 Transmit Timing Options 60
- 3.6.2 G.703 Interface 60
- 3.6.3 HSSI Interface 60
- 3.8 Ebem Framing Unit 62
- 3.8.2 Embedded Channel 62
- 3.9 STANAG Turbo Coding 62
- 3.10 FIPs TRANSEC Module 63
- 3.10.1.1 Key Agreement 63
- 3.10.1.2.1 Key Derivation 66
- DMD2050E 71
- DMD2050E CnC Module 71
- 3.11.6 Margin Requirements 77
- 3.11.15 Glossary 91
- 3.12.1 LDPC versus TPC 94
- 3.12.2 TPC and LDPC Summary 98
- 3.13 Reed-Solomon Codec 98
- 3.13.3 Interleaving 99
- Communications) 100
- 3.16 Standard IBS Mode 102
- 3.18 ESC Backward Alarms 103
- See also: 104
- 3.19.2 Aggregate Data Rate 106
- (less than In-Band Rate) 108
- Port labeled ASYNC (J17) 110
- Chapter 4. User Interfaces 113
- 4.2.2 Arrow Keys 114
- 4.2.3 Numeric Keys 114
- 4.2.4 LED Lights 115
- 4.3 Parameter Setup 116
- 4.3.1 Select a Parameter 116
- 4.4 Front Panel Main Menus 116
- 4.4.1.1 NETWORK SPEC (menu) 117
- 4.4.1.2 STRAP CODE 118
- 4.4.1.3 IF (menu) 118
- 4.4.1.4 DATA (menu) 118
- 4.4.1.5 REED-SOLOMON (menu) 121
- 4.4.1.6 AUPC (menu) 121
- 4.4.1.7 LOCAL AUPC (menu) 122
- 4.4.1.8 REMOTE AUPC (menu) 125
- 4.4.1.9 ITA (menu) 125
- 4.4.2.1 NETWORK SPEC (menu) 126
- 4.4.2.2 STRAP CODE 127
- 4.4.2.3 IF (menu) 127
- 4.4.2.4 DATA (menu) 128
- 4.4.2.5 REED-SOLOMON (menu) 129
- Hz) between the 130
- 4.4.3.1 TX SETUP (menu) 131
- 4.4.3.2 RX SETUP (menu) 134
- 4.4.3.3 GENERAL (menu) 136
- 4.4.4.1 LINK STATUS (menu) 137
- 4.4.4.2 VOLTAGES (menu) 139
- 4.4.4.3 CnC (menu) 139
- 4.4.4.4 ITA (menu) 139
- 4.4.6.1 FRONT PANEL (menu) 140
- 4.4.6.2 REMOTE CONTROL 140
- 4.4.6.3 TERMINAL (menu) 141
- 4.4.6.4 REMOTE PORT (menu) 141
- 4.4.6.5 TCP/IP (menu) 141
- 4.4.6.6 SNMP (menu) 143
- 4.4.6.7 FTP (menu) 144
- 4.4.6.8 WEB (menu) 144
- 4.4.6.9 TRANSEC (menu) 145
- 4.4.6.10.2 FEATURES (menu) 147
- 4.5 Terminal Mode Control 150
- 4.5.1 Terminal Mode Screens 150
- 5.1.1 Ground Connector 154
- 5.1.2 Power Switch 154
- 5.2 Front Panel Connections 155
- 5.2.1 Key Loader Interface 155
- 5.3 Rear Panel Connectors 156
- 5.3.2 EXT REF (J10) 157
- 5.3.4 ALARM (J15) 158
- 5.3.5 EXT CLK (J16) 159
- 5.3.6 ASYNC (J17) 160
- 5.3.8 MIL-188-114A (J19) 161
- Chapter 6. Maintenance and 163
- Troubleshooting 163
- 6.2 Troubleshooting 164
- 6.3 Alarms 165
- 6.3.2 Major Rx Alarms 165
- 6.3.3 Minor Tx Alarms 166
- 6.3.3.1 Minor Rx Alarms 167
- 6.4 Alarm Masks 170
- 6.4.1 Active Alarms 170
- 6.4.1.1 Major Alarms 170
- 6.4.1.2 Minor Alarms 170
- 6.4.3 Latched Alarms 171
- 6.4.4 Backward Alarms 173
- 6.5 IBS Alarms and Actions 174
- 7.1 Modulator 175
- 7.2 Demodulator 176
- 7.3 Plesiochronous Buffer 177
- 7.4 Monitor and Control 177
- 7.11 Data Rate Limits 179
- 7.11.1 Non-DVB 179
- 7.11.2 DVB 181
- 7.12 BER Specifications 183
- Sequential 184
- 184
- Viterbi Decoder Reed 185
- Turbo Decoder 186
- Trellis 187
- Viterbi 189
- Viterbi Decoder 190
- Reed Solomon 190
- LDPC Decoder 196
- MILSTD 188-165B 200
- MILSTD 188 201
- 7.13 AGC Output Voltage 208
- Appendix A. Product Options 209
- B.1 Introduction 211
- B.2 Required Equipment 211
- B.3 Procedures 211
- B.3.2 Record the Unit ID 213
- B.3.4 Install the Code 214
- Appendix C. Carrier Control 217
- C.3 Carrier States 218
- C.3.1 Carrier OFF 218
- C.3.2 Carrier ON 218
- C.3.3 Carrier AUTO 218
- C.3.4 Carrier VSAT 219
- C.3.5 CARRIER RTS 219
- Appendix D. Web Interface 221
- Setup Guide 221
- D.2.2 IP Address 222
- D.3 Web Interface Security 222
- D.3.1 Default User Accounts 222
- D.3.2 User Account Data 223
- D.1 User Account Setup 223
- D.1.1 Edit the User ID 224
- D.1.2 Edit the Access Group 224
- D.2 Reset a User Account 225
- D.3 Confirmation 225
- D.4 Equipment Website 226
- D.5 Web Page Appearance 228
- D.6.3.1 Change the encoding 233
- D.6.4.4 Change the encoding 238
- D.6.5.2 Change the encoding 241
- E.1 Introduction 243
- E.2 System Requirements 243
- E.3 Configuration Examples 244
- Figure E-1. Looped Modems 245
- E.4 Functional Descriptions 246
- E.4.1 Drop Only 246
- E.4.2 Insert Only 246
- E.4.3 Data Formats 248
- E.4.3.1 PCM-30 248
- E.4.3.2 PCM-30C 248
- E.4.3.3 PCM-31 248
- E.4.3.4 PCM-31C 249
- E.4.3.5 T1-D4/T1-D4-S 249
- E.4.3.6 T1-ESF/T1-ESF-S 249
- E.5.1 Data Rate 253
- Example 1: 255
- Example 2: 257
- E.8 Prerequisite 266
- F.1 Introduction 271
- F.4 Ethernet Test 274
- Network) 274
- Appendix G. AUPC Operation 279
- G.1.2 EF AUPC 280
- G.1.3 Near Side AUPC 280
- G.1.4 EBEM AUPC 281
- Appendix H. Ethernet Data 283
- Interface Setup 283
- H.1.1 Ethernet Flow Control 284
- H.1.2 Ethernet Daisy Chain 284
- H.1.3 Ethernet QOS Type 285
- H.1.4 Ethernet QOS Queue 285
- H.1.6 Packet Statistics 287
- Appendix I. Strap Codes 289
- I.2 Sample Applications 294
- Appendix J. ITA Operation 303
- J.1.2 Basic Setup (Example) 305
- Table J-3 - ITA Setup 313
- TRANSEC Module 333
- 480 • 333 • 2200 PHONE 342
- • 333 • 2161 FAX 342
Related products and manuals for Networking Comtech EF Data DMD-2050E
Networking Comtech EF Data CDM-Qx Specifications
(258 pages)
(258 pages)
Networking Comtech EF Data CDM-Qx Specifications
(260 pages)
(260 pages)
© 2020, manymanuals.com. All rights reserved. | 0.048 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals