Comtech-ef-data SNM-1000 User Manual Page 94
- Page / 184
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
SNM-1000 Node Control Modem Revision 3
Operation MN/SNM1000.IOM
3–52
3.7 SNM-1000 Commands
The commands described in this section are used to set SNM-1000 functional parameters
within a DAMA environment. Refer to Appendix A for commands used to communicate
with external modems attached to an SNM-1000.
3.7.1 Character Set
The interface responds to ASCII characters in the range of 0x00 to 0x7F. The 8th bit
(most significant) is not generated on the transmit side and is ignored on the receive side.
3.7.2 Status Lines and Flow Control
The interface ignores all status inputs.
3.7.3 Message Structure
A message is either a command or a response. Each message is made up of three
elements:
• Prefix
• Message body
• End character
3.7.3.1 Prefix
The prefix consists of the channel number in ASCII decimal, with a valid range of 0
through 30. Leading zeros are ignored. Prefix 0 is valid for an SNM-1000 Node Control
modem and prefixes 1 through 30 are valid for external traffic modems attached to the
SNM-1000 such as SDM-300s, SDM-6000s, etc.
- Node Control Modem 1
- Installation and O 1
- SNM-1000 3
- Procedural Steps 4
- Network Support Customer Plan 5
- Table of Contents 7
- Preface MN/SNM1000.IOM 11
- Figures 12
- About this Manual 13
- Related Documents 13
- Conventions and References 13
- Cautions and Warnings 13
- Metric Conversion 14
- Trademarks 14
- Electrical Safety 15
- Environmental 15
- Installation 16
- IMPORTANT 17
- European EMC Directive 18
- Warranty Policy 19
- Limitations of Warranty 19
- Exclusive Remedies 19
- Disclaimer 19
- Chapter 1. INTRODUCTION 21
- 1.1 Overview 22
- 1.1.1 Additional Features 22
- 1.1.2 Mode of Operation 23
- 1.2 Description 24
- 1.3 Options 25
- 1.4 Specifications 26
- 1.4.1 General Specifications 26
- Introduction MN/SNM1000.IOM 27
- 1.4.3 DAC Specification 28
- 1.6 Dimensional Envelope 31
- Chapter 2. INSTALLATION 33
- 2.2 Installation 34
- Installation MN/SNM1000.IOM 35
- 2.3 Rear Panel Connections 36
- 2.3.1 EFBUS1/2 Port (J6) 37
- 2.3.3 User Port 39
- ≥ 0 dBm 42
- Chapter 3. OPERATION 43
- 3.1.1 LED Indicators 44
- 3.1.2 Front Panel Keypad 45
- 3.2 Menu System 46
- 3.3 Front Panel Menu 47
- 3.4 OPENING SCREEN 48
- MODEM REFERENCE 51
- INTERNAL 51
- CONFIGURATION 51
- DEMODULATOR 51
- TX CLOCK PHASE 55
- EXT-CLK FREQ 55
- 1544.000 KHZ 55
- BUFFER CLOCK 56
- RX (SATELLITE) 56
- RX CLOCK PHASE 56
- B-BAND LOOP BACK 57
- BUFFER SIZE 58
- 384 BITS 58
- BUFFER CENTER 58
- 3.4.1.4 CONFIGURATION:SAVE 59
- 3.4.2.1 MONITOR:RAW BER 60
- 3.4.2.3 MONITOR:EB/NO 61
- 3.4.2.6 MONITOR:BUFFER FILL 61
- FUNCTION SELECT 62
- FAULTS/ALARMS 62
- MODULATOR 63
- + 63
- +-++ 63
- TX INTERFACE 64
- 64
- RX INTERFACE 65
- STORED FLTS/ALAMS 67
- Reed-Solomon option only 70
- UTILITY 71
- 3.4.5.1 UTILITY:MODULATOR 72
- 3.4.5.1.7 MODULATOR:TX MODE 74
- 3.4.5.2 UTILITY:DEMODULATOR 75
- 3.4.5.3 UTILITY:INTERFACE 77
- 3.4.5.4 UTILITY:NETWORK 80
- 3.4.5.4.1 NETWORK:RELEASE 80
- 3.4.5.5 UTILITY:SYSTEM 81
- 3.4.5.5.1 SYSTEM:TIME/DATE 81
- 3.4.5.5.4 SYSTEM:REMOTE TYPE 82
- MASTER RESET 86
- HARD/SOFT 86
- 3.4.5.6 UTILITY:MODEM TYPE 87
- MODEM OPTIONS 89
- 3.5 User Port Operation 92
- 3.6.1 User Port Modem 93
- 3.6.2 Remote Site Modem 93
- 3.7 SNM-1000 Commands 94
- 3.7.1 Character Set 94
- 3.7.3 Message Structure 94
- 3.7.3.1 Prefix 94
- 3.7.3.2 Message Body 95
- 3.7.3.3 End Character 95
- 3.7.3.4 Case Sensitivity 95
- 3.7.3.5 Delimiters 95
- 3.7.3.6 End Character 95
- 3.7.3.7 Queries 96
- 3.7.4 Node Address (NA) 96
- 3.7.4.1 Command Format 96
- SNM-1000 transmit power 98
- 3.7.12 SNM-1000 Mode (MD) 100
- 3.7.12.1 Command Format 100
- 3.7.13.1 Help Screen 101
- 3.7.13.2 Flash Updates 101
- 3.7.13.6 Ram Test 102
- 3.7.13.3 PDREM Ram 102
- 3.7.13.4 Area1 Defaults 102
- 3.7.13.5 Area2 Defaults 102
- 3.7.15.1 Command Format 104
- 3.7.16 Channel Type (CT) 104
- 3.7.16.1 Command Format 104
- 3.7.17.1 Command Format 105
- 3.7.18 Data Call 106
- 3.7.18.1.1 Command Format 106
- Operation MN/SNM1000.IOM 107
- 3.7.18.2.1 Command Format 108
- 3.7.19 Terminate (TE) 108
- 3.7.19.1 Command Format 108
- 3.7.20.1 Command Format 109
- 3.7.20.3 Example 110
- 3.7.21.1 Command Format 111
- 3.7.22.1 Command Format 112
- 3.7.23.1 Command Format 113
- 3.7.24.1 Command Format 114
- 3.7.25.1 Command Format 115
- 3.7.26.1 Command Format 116
- 3.7.27 Port Redirection 116
- 3.7.28.1 Command Format 117
- (part of J1) 120
- CONNECTOR 120
- 4.1.1 Specifications 121
- 4.1.2 Theory of Operation 121
- 4.1.2.1 User Port 121
- 4.1.4 Monitor and Control 122
- 4.1.5 Non-Volatile Memory 123
- 4.1.6 User Port 123
- 4.2 Modulator 124
- 4.2.1 Theory of Operation 126
- 4.2.1.1 Burst Mode 126
- 4.2.2.1 QPSK Encoding 127
- 4.3 Demodulator 128
- 4.3.1 Theory of Operation 129
- 4.3.1.1 Continuous Mode 129
- Chapter 5. MAINTENANCE 131
- 5.1.1 System Faults/Alarms 132
- Maintenance MN/SNM1000.IOM 133
- 5.1.2 Faults/Alarms Display 136
- 5.1.3 Faults/Alarms Analysis 136
- 5.1.3.1 Modulator Faults 137
- 5.1.3.1.1 Modulator Checkout 138
- 5.1.3.2 Demodulator Faults 141
- WITH NOISE 143
- WITHOUT NOISE 143
- Appendix A. REMOTE CONTROL 149
- OPERATION 149
- A.2.1 Character Set 150
- A.2.3 Message Structure 150
- Command: 152
- is added to the 152
- (MPO_) 152
- A.5.1 Interface Buffer Size 158
- A.6.1 Modem Type Commands 160
- A.7 Configuration Status 160
- Modulator Output Power 161
- A.7.1 Modem Faults Status 163
- A.8 Stored Faults 168
- A.9 Unsolicited Responses 177
- A.9.1 Messages from NMS 177
- A.9.2 List of Cause Codes 178
- METRIC CONVERSIONS 183
- Units of Length 183
- Temperature Conversions 183
- Units of Weight 183
- 480 • 333 • 2200 PHONE 184
- 480 • 333 • 2161 184
Related products and manuals for Equipment Comtech-ef-data SNM-1000
Equipment Comtech-ef-data SDM-9000 User Manual
(256 pages)
(256 pages)
Equipment Comtech-ef-data SNM-1002 User Manual
(170 pages)
(170 pages)
Equipment Comtech-ef-data SNM-1010L User Manual
(266 pages)
(266 pages)
Equipment Comtech-ef-data SNM-1001L User Manual
(344 pages)
(344 pages)
Equipment Comtech-ef-data DD2401 User Manual
(98 pages)
(98 pages)
Equipment Comtech-ef-data MD2401 User Manual
(106 pages)
(106 pages)
Equipment Comtech-ef-data CLC-10 User Manual
(70 pages)
(70 pages)
Equipment Comtech-ef-data HPOD User Manual
(150 pages)
(150 pages)
Equipment Comtech-ef-data DST User Manual
(66 pages)
(66 pages)
Equipment Comtech-ef-data CPLINK User Manual
(26 pages)
(26 pages)
Equipment Comtech-ef-data CiLink User Manual
(38 pages)
(38 pages)
Equipment Comtech-ef-data LPOD-R User Manual
(154 pages)
(154 pages)
Equipment Comtech-ef-data LPOD User Manual
(218 pages)
(218 pages)
Equipment Comtech-ef-data KP-10 User Manual
(44 pages)
(44 pages)
© 2020, manymanuals.com. All rights reserved. | 0.089 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals