Comtech-ef-data CST-5000 User Manual Page 65
- Page / 149
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
CST-5000 C-Band Satellite Terminal Redundant System Installation
Rev. 9 3–11
c. With the RFTs side-by side,
position a 20 inch (51 cm)
unistrut (open side facing
up) in place over one pair of
8 inch (20.3 cm) unistruts.
Ensure the long unistrut is
centered over the RFT.
d. Using two or three 5/16-18
x 1-1/4 inch (6 mm) bolts,
5/16 inch (8 mm) split
lockwashers, and 5/16 inch
(8 mm) flat washers, attach
the 20 inch (51 cm) unistrut
to the 8 inch (20.3 cm)
unistruts.
Tighten the bolts firmly.
e. Attach the second 20 inch (51 cm) unistrut to the second set of 8 inch
(20.3 cm) unistruts by repeating Steps 3.a. through 3.d.
4. Install the pipe blocks as follows:
a. Install two spring nuts in each of the two 20 inch (51 cm) long unistruts and
two 14 inch (35.6 cm) long unistruts (centered in the unistruts, and wide
enough apart so the pipe blocks will clear the pole when the unit is installed).
b. Install each spring nut as follows:
(1) Place the spring nut in the unistrut channel, spring side down, with its
wide side parallel with the unistrut channel.
(2) Press down on the spring nut to compress the spring, and rotate the nut
90° (i.e., perpendicular to the unistrut).
(3) Release pressure on the spring nut.
- C-Band Satellite Terminal 1
- Installation and O 1
- Errata A 2
- Filename: T_ERRATA 2 3
- Errata B 5
- CST-5000 7
- Customer Support 8
- Table of Contents 9
- Preface CST-5000 10
- CST-5000 Preface 11
- Rev. 9 v 11
- Figures 12
- About this Manual 13
- Related Documents 13
- Conventions and References 13
- Cautions and Warnings 13
- Metric Conversion 14
- Trademarks 14
- Warranty Policy 15
- Limitations of Warranty 15
- Exclusive Remedies 15
- Disclaimer 15
- Rev. 9 1–1 17
- 1.1 Description 18
- Rev. 9 1–3 19
- 1.1.1 Applications 20
- 1.1.4 Outdoor Enclosure 21
- 1.2 Options 22
- 1.2.1 Configurations 22
- 1.2.2 Equipment 23
- 1.3 Specifications 24
- > 250 kHz Carrier Offset 25
- ± 1 dB/575 MHz 27
- ± 3 dB maximum 27
- ± 0.01 ns/MHz maximum 27
- 1–12 Rev. 9 28
- SINGLE THREAD SYSTEM 29
- INSTALLATION 29
- 2.2.1 Included Parts 30
- 2.3 RFT Installation 35
- 2.3.1 Tools Required 36
- 2.3.2.1 Round Pole 37
- 2–10 Rev. 9 38
- Rev. 9 2–11 39
- 2–12 Rev. 9 40
- Rev. 9 2–13 41
- 2–14 Rev. 9 42
- Rev. 9 2–15 43
- 2.3.2.2 Square Pole 44
- 2.3.3 Spar Installation 45
- 2–18 Rev. 9 46
- 2.4 LNA Installation 47
- 2–20 Rev. 9 48
- 2.5 External Connections 49
- 2.5.1 TX/IF Input (J1) 50
- 2.5.2 TX/RF Output (J2) 50
- 2.5.3 RX/IF Output (J3) 50
- 2.5.4 RX/RF Input (J4) 51
- 2.5.5 Prime Power (J5) 51
- 2–24 Rev. 9 52
- 2.5.7 Ground (GND) 54
- REDUNDANT SYSTEM 55
- 3.1 Unpacking 56
- 3.2.1 Included Parts 57
- 3.3 RFT Installation 61
- 3.3.1 Tools Required 62
- 3.3.2.1 Round Pole 63
- 3–10 Rev. 9 64
- Rev. 9 3–11 65
- 3–12 Rev. 9 66
- Rev. 9 3–13 67
- 3.3.2.2 Square Pole 68
- 3.3.3 Spar Installation 69
- 3–16 Rev. 9 70
- Rev. 9 3–17 71
- 3–18 Rev. 9 72
- Rev. 9 3–19 73
- 3.4 External Connections 74
- Rev. 9 3–21 75
- OPERATION 76
- • Configuration (CONFIG) 77
- • Monitor 77
- • Faults 77
- 4.3.1 Front Panel Controls 78
- 4.4 Menu Explanations 79
- 4.4.1 Configuration 80
- 4–6 Rev. 9 81
- 4.4.2 Monitor 84
- 4–10 Rev. 9 85
- 4.4.3 Faults 86
- 4–12 Rev. 9 87
- 4–14 Rev. 9 89
- THEORY OF OPERATION 90
- Figure 5-1. M&C Board 91
- 5.1.1 EEPROM Memory 92
- 5.1.2 Remote Interface 92
- 5.1.4 Theory of Operation 93
- Rev. 9 5–5 94
- 5.1.6 Test Points and LEDs 99
- 5.2.1 Specifications 99
- HIGH STABILIT 100
- OSCILLATOR 100
- 5.3 IF Local Oscillator 101
- 5.3.1 Specifications 101
- Rev. 9 5–13 102
- 5.4.1 Specifications 103
- 5.4.2 Theory of Operation 103
- 5.4 Synthesizer 103
- Rev. 9 5–15 104
- 5.5 Down Converter 105
- 5.5.1 Specifications 106
- 5.5.2 Theory of Operation 107
- 5.6 Up Converter 108
- 5.6.1 Specifications 109
- 5.6.2 Theory of Operation 110
- 5–22 Rev. 9 111
- 6.1 Test Points and LEDs 112
- 6.2 Fault Isolation 113
- Table 6-3. Fault Isolation 114
- Rev. 9 6–5 116
- 6–6 Rev. 9 117
- Rev. 9 6–7 118
- 6–8 Rev. 9 119
- Appendix A 120
- OPTIONS 120
- A–2 Rev. 9 121
- A.1.1.1 Specifications 122
- A.1.2 Synthesizer 122
- A.1.2.1 Specifications 122
- A.1.2.2 Theory of Operation 122
- A–4 Rev. 9 123
- A.1.3 Down Converter 124
- A.1.3.1 Specifications 125
- A.1.3.2 Theory of Operation 126
- A.1.4 Up Converter 127
- A.1.4.1 Specifications 128
- A.1.4.2 Theory of Operation 129
- Rev. 9 A–11 130
- A–12 Rev. 9 131
- A.2.3 M&C Software 132
- A–14 Rev. 9 133
- Appendix B 134
- REMOTE CONTROL OPERATION 134
- B.2 Message Structure 135
- B.2.1 Start Character 135
- B.2.2 Device Address 136
- B.2.3 Command/Response 136
- B.2.4 End Character 137
- Rev. 9 B–5 138
- B–6 Rev. 9 139
- Rev. 9 B–7 140
- B–8 Rev. 9 141
- Glossary 142
- Ω kilo-ohms 143
- METRIC CONVERSIONS 148
- Units of Length 148
- Temperature Conversions 148
- Units of Weight 148
- 480 • 333 • 2200 PHONE 149
- 480 • 333 • 2161 149
Related products and manuals for Equipment Comtech-ef-data CST-5000
Equipment Comtech-ef-data turboIP-G2 User Manual
(172 pages)
(172 pages)
Equipment Comtech-ef-data C5 User Manual
(332 pages)
(332 pages)
Equipment Comtech-ef-data HPCST-5000 User Manual
(204 pages)
(204 pages)
Equipment Comtech-ef-data KST-12025 User Manual
(124 pages)
(124 pages)
Equipment Comtech-ef-data KST-12000 User Manual
(122 pages)
(122 pages)
Equipment Comtech-ef-data SFC1800A User Manual
(140 pages)
(140 pages)
Equipment Comtech-ef-data HPCST-5000 User Manual
(172 pages)
(172 pages)
© 2020, manymanuals.com. All rights reserved. | 0.042 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals