Comtech-ef-data HPCST-5000 User Manual Page 116
- Page / 204
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Operation High-Power C-Band Satellite Terminal
5–4 Rev. 0
5.4 Main Menu
Refer to Figure 5-2.
The following sections contain information about individual menu categories and their
functions.
Note: The firmware/software referenced in this manual may be an earlier version of the
actual firmware/software supplied with the unit.
RFT-500
VER: 7.00 or
VER: 8:00
SELECT
CONFIG
(Figure 5-3)
SELECT
MONITOR
(Figure 5-4)
SELECT
FAULTS
(Figure 5-5)
ACCESS TO
SUBMENU
CONDITIONAL OR
OPTION-DEPENDENT
Parameter Information
Key:
Figure 5-2. Main Menu
- HPCST-5000 1
- HPCST-5000HPCST-5000 1
- Warranty Policy 4
- Limitations of Warranty 4
- Exclusive Remedies 4
- Disclaimer 4
- About this Manual 5
- Cautions and Warnings 5
- Trademarks 5
- Related Documents 6
- Customer Support 7
- Table of Contents 9
- Rev. 0 vii 11
- Rev. 0 ix 13
- Rev. 0 xi 15
- Chapter 1 17
- INTRODUCTION 17
- 1.2 Applications 19
- 1.3 Options 20
- Rev. 0 1–5 21
- 1.4 Configurations 22
- Rev. 0 1–7 23
- 1.4.2 Redundant System 24
- 1.5 Component Descriptions 25
- 1–10 Rev. 0 26
- Rev. 0 1–11 27
- 1–12 Rev. 0 28
- Rev. 0 1–13 29
- Table 1-4. HPCST Models 30
- 1.7 HPCST-5000 Specifications 31
- 1.7.2 System Interfaces 31
- 1.7.3 System 32
- Environment Specification 32
- 1.7.7 Leading Particulars 36
- 1.8 RFT Specification 37
- 1.10 LNA Specification 40
- 1.11 Dimensional Drawings 41
- 1–26 Rev. 0 42
- Rev. 0 1–27 43
- 1–28 Rev. 0 44
- Chapter 3 55
- Single Thread Configuration 55
- 3–2 Rev. 0 56
- 3.1 Unpacking 57
- RFINRFOUT 58
- MODELNO 58
- SERIALNO 58
- FREQUENCY 58
- NOISETEMPGAIN 58
- 3.3 RFT Installation 59
- 3.3.1 Tools Required 60
- 3.3.2.1 Round Pole 61
- 3–8 Rev. 0 62
- Rev. 0 3–9 63
- 3–10 Rev. 0 64
- Rev. 0 3–11 65
- 3–12 Rev. 0 66
- Rev. 0 3–13 67
- 3.3.2.2 Square Pole 68
- 3.3.3 Spar Installation 68
- Rev. 0 3–15 69
- 3.4 LNA Installation 70
- Rev. 0 3–17 71
- 3.5 C-Band SSPA Installation 72
- 3.5.2.1 Round Pole 73
- 3–20 Rev. 0 74
- Rev. 0 3–21 75
- 3–22 Rev. 0 76
- Rev. 0 3–23 77
- 3–24 Rev. 0 78
- 3.5.2.2 Square Pole 79
- 3.5.3 Spar Installation 80
- Rev. 0 3–27 81
- 3–28 Rev. 0 82
- Chapter 4 83
- REDUNDANT SYSTEM 83
- INSTALLATION 83
- 4–2 Rev. 0 84
- 4.1 Unpacking 85
- 4.2 Inspecting the Equipment 86
- 4.2.1 Included Parts 86
- 4.3 RFT Installation 88
- 4.3.1 Tools Required 89
- 4.3.2.1 Round Pole 90
- Rev. 0 4–9 91
- 4–10 Rev. 0 92
- Rev. 0 4–11 93
- 4–12 Rev. 0 94
- Rev. 0 4–13 95
- 4.3.2.2 Square Pole 96
- 4.3.3 Spar Installation 97
- 4–16 Rev. 0 98
- Rev. 0 4–17 99
- 4–18 Rev. 0 100
- Rev. 0 4–19 101
- 4–20 Rev. 0 102
- 4.3.5.1 Round Pole 103
- 4–22 Rev. 0 104
- Rev. 0 4–23 105
- 105
- 4–24 Rev. 0 106
- Rev. 0 4–25 107
- 4.3.5.2 Square Pole 108
- 4.3.6 Spar Installation 109
- 4–28 Rev. 0 110
- Rev. 0 4–29 111
- 4–30 Rev. 0 112
- Chapter 5 113
- OPERATION 113
- ! Monitor 114
- 5.3.1 Front Panel Controls 115
- 5.4 Main Menu 116
- 5.4.1 Configuration 117
- ACCESS TO 118
- CONDITIONAL OR 118
- OPTION-DEPENDENT 118
- Parameter Information 118
- 5.4.2 Monitor 121
- 5–10 Rev. 0 122
- 5.4.3 Faults 123
- 5–14 Rev. 0 126
- Chapter 6 127
- THEORY OF OPERATION 127
- Figure 6-1. M&C Board 128
- 6.1.1 EEPROM Memory 129
- 6.1.2 Remote Interface 129
- 6.1.4 Theory of Operation 130
- Rev. 0 6–5 131
- 6.1.6 Test Points and LEDs 136
- 6.2.1 Specifications 136
- Rev. 0 6–11 137
- 6.3 IF Local Oscillator 138
- 6.3.1 Specifications 138
- Rev. 0 6–13 139
- 6.4 Synthesizer 140
- 6.4.1 Specifications 140
- 6.4.2 Theory of Operation 140
- Rev. 0 6–15 141
- 6–16 Rev. 0 142
- 6.5 Down Converter 143
- 6.5.1 Specifications 144
- 6.5.2 Theory of Operation 145
- 6.6 Up Converter 146
- 6.6.1 Specifications 147
- 6.6.2 Theory of Operation 148
- Chapter 7 149
- MAINTENANCE 149
- 7.2 Fault Isolation 150
- Table 7-3. Fault Isolation 151
- Rev. 0 7–5 153
- POWERSUPPLY 154
- Chapter 8 155
- EQUIPMENT LIST 155
- Table 8-2. Redundant System 156
- 8.2 Detail Equipment List 157
- 8.2.1 LNA Connector Kit 157
- 8–4 Rev. 0 158
- 8.2.2 Cable Kit 159
- - Item Not Illustrated 160
- Rev. 0 8–7 161
- 8–8 Rev. 0 162
- 8.2.3 Spar Mounting Kit 163
- 8–10 Rev. 0 164
- 8.2.4 Universal Mounting Kit 165
- 8–12 Rev. 0 166
- 8–14 Rev. 0 168
- 8–16 Rev. 0 170
- Appendix A 171
- CONFIGURATIONS 171
- A.1.1.1 Specifications 172
- A.1.2 Synthesizer 173
- A.1.2.1 Specifications 173
- A.1.2.2 Theory of Operation 173
- A–4 Rev. 0 174
- A.1.3 Down Converter 175
- A.1.3.1 Specifications 175
- DOWN CONVERTER 176
- A.1.3.2 Theory of Operation 177
- A.1.4 Up Converter 178
- A.1.4.1 Specifications 178
- Rev. 0 A–9 179
- A.1.4.2 Theory of Operation 180
- Appendix B 181
- REMOTE CONTROL OPERATION 181
- B.2.1 Start Character 182
- B.2.2 Device Address 182
- B.2 Message Structure 182
- B.2.3 Command/Response 183
- B.2.4 End Character 183
- B–4 Rev. 0 184
- Rev. 0 B–5 185
- B.4 System 186
- B.5 Status Commands/Responses 187
- B–8 Rev. 0 188
- Glossary 189
- Chapter 2 195
- EXTERNAL CONNECTIONS 195
- 2.1.1.1 TX/IF Input (J1) 196
- 2.1.1.2 TX/RF Output (J2) 197
- 2.1.1.3 RX/IF Output (J3) 197
- 2.1.1.4 RX/RF Input (J4) 197
- 2.1.1.5 Prime Power (J5) 198
- (see Note 1) 199
- (see Note 1 199
- (see Note 2) 199
- (see Note 3) 199
- 2.1.1.7 Ground (GND) 200
- 2.1.2.5 Prime Power (J5) 203
- 2.1.2.6 RF Output (J7) 203
- 2.1.2.7 Alarm/Interface Board 204
Related products and manuals for Equipment Comtech-ef-data HPCST-5000
Equipment Comtech-ef-data KST-12025 User Manual
(124 pages)
(124 pages)
Equipment Comtech-ef-data KST-12000 User Manual
(122 pages)
(122 pages)
Equipment Comtech-ef-data SFC1800A User Manual
(140 pages)
(140 pages)
Equipment Comtech-ef-data HPCST-5000 User Manual
(172 pages)
(172 pages)
© 2020, manymanuals.com. All rights reserved. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals